Anti-Slip Spray for Tile Floors, Bathtubs & Showers
- Enhanced Slip Resistance: Increases safety in wet and slippery areas such as bathtubs, showers, tile floors, pool areas, steps, and boats.
- Versatile Application: Suitable for a variety of surfaces including fiberglass, acrylic, ceramic, porcelain tiles, concrete, metal, and properly prepared wood.
- Transparent and Durable: Leaves a clear, durable, and lightly textured finish that is both barefoot and paw-friendly without altering the appearance of your surfaces.
- Weather and Oil Resistant: Once dried, the self-priming coating is completely resistant to oil and weather, making it ideal for both interior and exterior use.
- Long-Lasting Protection: Each can covers approximately 2 square meters and comes with a 2-year manufacturer’s warranty, ensuring long-term slip resistance.
- One Can: Up to 2 sq. m.
SlipDoctors anti-slip spray coating is the ideal solution to increase the slip resistance on wet and slippery areas such as bathtubs, showers, tile floors, pool areas, steps, and boats. The self-priming nonslip coating is easily applied and can be used on interior and exterior surfaces as it is completely oil and weather resistant once dried.
The final finish of the SlipDoctors anti-slip spray is a durable and lightly textured anti-slip spray coating that is barefoot and paw-friendly. The anti-slip spray is not limited to fibreglass and acrylic but can also be used on many other slippery surfaces like ceramic and porcelain tiles, concrete, metal, and properly prepared wood.
Not only is SlipDoctors Non-Slip Spray highly effective, but it's also incredibly versatile. Whether you're looking to make your bathroom safer or simply want to improve the slip-resistance of your tiles or fibreglass surfaces, our anti-slip spray is the ideal solution.
Each can of SlipDoctors anti-slip spray can protect an area roughly 2 square metres and once correctly applied is protected by the 2-year SlipDoctors Manufacturer’s Warranty.
Important: When applying to porcelain bathtubs, please repair any chips prior to application. Repair kits can be purchased at your local home improvement store. We do not recommend using black sandpaper, as it can leave behind small black dots that may be visible after using the clear spray.
Surface Preparation: Always test a small area for color compatibility and adhesion. Fiberglass/Acrylic:Lightly sand with 220 grit sand paper to promote adhesion. Clean surface with soap and water or wipe with clean cloth and lacquer thinner (or another cleaner that does not leave residue) to remove all sanding dust. Allow it to dry thoroughly. For other surface preparation instructions, please see the Technical Data Sheet
Application:
- Step 1: Surface should be dry, clean and free of oil, wax, dirt, loose paint and other contaminants.
- Step 2: After entire surface is completely dry, properly ventilate room by opening windows, doors, turning on ceiling fans, etc.
- Step 3: Tape off application area with painters tape.
- Step 4: Mix contents of can well by shaking until the ball rattles within the can. Once ball rattles, continue to shake vigorously for 2-3 minutes. During use, shake intermittently for 10 seconds to keep product mixed.
- Step 5: Use painters paper to protect surround-ing areas from overspray. (Figure B)Spray 6 - 12 inches away from surface in a sweeping motion during application. Applying 2-3 light coats will cure, protect and look better than one heavy coat.
- Step 6: If spray stops or is irregular, turn can upside down and spray for 2-3 seconds to clear nozzle. Wipe tip, shake can and resume.
- Step 7: Slowly remove all tape and paper shortly after application. Allow 24 hours before use to allow product to fully cure. If product will be subject to prolonged periods of soaking in water, allow 48 hours before use to fully cure.
Clean Up and Removal: For effective maintenance and safe storage, follow these guidelines: To remove overspray, use paint thinner or lacquer thinner. It's crucial to clean the valve immediately before storing a partially used can. Hold the can upside down and spray until only clear gas dispenses (about 3 to 5 seconds), then wipe the tip before storage. Should the spray valve get clogged, remove and clean it using lacquer thinner, ensuring the opening faces away from the body during replacement. For product removal, if desired, acetone can be used. For comprehensive instructions, consult the Non-Slip Spray Clear and White Technical Data Sheet.
